Community


All times are UTC - 5 hours




Post new topic Reply to topic  [ 5 posts ] 
Author Message
 Post subject: Need Help With D-link Dir825 Router set up
PostPosted: Tue Oct 16, 2012 12:38 pm 
Offline

Joined: Mon Jun 27, 2011 10:49 am
Posts: 22
HI

is it possible for me to to set up server and client both in this router

Thanks


Top
 Profile  
 
 Post subject: Re: Need Help With D-link Dir825 Router set up
PostPosted: Tue Oct 16, 2012 8:29 pm 
Offline

Joined: Sun Nov 16, 2008 6:41 am
Posts: 1869
Hi danny11542,

We didn't test NR on this model yet, but NR may work on it, as some model of the router has 8MB/16MB flash and a Atheros AR7161 CPU.

Thanks,
KevinZ - NeoRouter team


Top
 Profile  
 
 Post subject: Re: Need Help With D-link Dir825 Router set up
PostPosted: Wed Oct 24, 2012 8:37 am 
Offline

Joined: Mon Jun 27, 2011 10:49 am
Posts: 22
where can i get how to config openwrt for NR Client i have install perfect log in to server good but from their i can not go any further i have brink 2 router try to config after install will the openwrt is firmware it works same in every router after install can some one give me guide on how to get all LAN devices to get on NR router client i have search everywhere on internet but i found step by step instructions on openvpn but it work different then NR can some one please give me step by step instruction on how can i get this client to get it going i need guide for after install

Thanks


Top
 Profile  
 
 Post subject: Re: Need Help With D-link Dir825 Router set up
PostPosted: Fri Oct 26, 2012 8:49 am 
Offline

Joined: Sun Nov 16, 2008 6:41 am
Posts: 1869
Hi danny11542,

Once you sign in from your box to the NR server, the box has been registered and been part of the VLAN. Then the devices in the VLAN can communicate each other. Did you try ping, ssh and so on?

You may also take a look at this:
http://www.neorouter.com/wiki/index.php ... or_OpenWrt

or the user manual, chapter 2.3.6:

http://download.neorouter.com/Documents ... l_15en.pdf

Let us know if you still have problem.

Thanks,
KevinZ - Neorouter team


Top
 Profile  
 
 Post subject: Re: Need Help With D-link Dir825 Router set up
PostPosted: Sat Oct 27, 2012 9:40 am 
Offline

Joined: Mon Jun 27, 2011 10:49 am
Posts: 22
i have fellow the exact step you should but no luck i can not access devices on NR here is the log file may be it help see what i am doing wrong
Oct 27 10:03:00 NRVPN1 daemon.info dnsmasq-dhcp[1348]: DHCPDISCOVER(br-lan) 00:23:8b:af:0e:ed
Oct 27 10:03:00 NRVPN1 daemon.info dnsmasq-dhcp[1348]: DHCPOFFER(br-lan) 192.168.1.204 00:23:8b:af:0e:ed
Oct 27 10:03:07 NRVPN1 cron.err crond[1296]: time disparity of 597487 minutes detected
Oct 27 10:03:16 NRVPN1 daemon.info dnsmasq-dhcp[1348]: DHCPDISCOVER(br-lan) 00:23:8b:af:0e:ed
Oct 27 10:03:16 NRVPN1 daemon.info dnsmasq-dhcp[1348]: DHCPOFFER(br-lan) 192.168.1.204 00:23:8b:af:0e:ed
Oct 27 10:04:01 NRVPN1 cron.err crond[1296]: USER root pid 1720 cmd /usr/bin/nrcronclient
Oct 27 10:05:01 NRVPN1 cron.err crond[1296]: USER root pid 1954 cmd /usr/bin/nrcronclient
Oct 27 10:06:01 NRVPN1 cron.err crond[1296]: USER root pid 2188 cmd /usr/bin/nrcronclient
Oct 27 10:07:01 NRVPN1 cron.err crond[1296]: USER root pid 2422 cmd /usr/bin/nrcronclient
Oct 27 10:08:01 NRVPN1 cron.err crond[1296]: USER root pid 2656 cmd /usr/bin/nrcronclient
Oct 27 10:09:01 NRVPN1 cron.err crond[1296]: USER root pid 2890 cmd /usr/bin/nrcronclient
Oct 27 10:09:07 NRVPN1 daemon.info dnsmasq-dhcp[1348]: DHCPDISCOVER(br-lan) 00:23:8b:af:0e:ed
Oct 27 10:09:07 NRVPN1 daemon.info dnsmasq-dhcp[1348]: DHCPOFFER(br-lan) 192.168.1.204 00:23:8b:af:0e:ed
Oct 27 10:09:07 NRVPN1 daemon.info dnsmasq-dhcp[1348]: DHCPREQUEST(br-lan) 192.168.1.204 00:23:8b:af:0e:ed
Oct 27 10:09:07 NRVPN1 daemon.info dnsmasq-dhcp[1348]: DHCPACK(br-lan) 192.168.1.204 00:23:8b:af:0e:ed Home-PC
Oct 27 10:10:01 NRVPN1 cron.err crond[1296]: USER root pid 3124 cmd /usr/bin/nrcronclient
Oct 27 10:11:01 NRVPN1 cron.err crond[1296]: USER root pid 3358 cmd /usr/bin/nrcronclient
Oct 27 10:12:01 NRVPN1 cron.err crond[1296]: USER root pid 3592 cmd /usr/bin/nrcronclient
Oct 27 10:13:01 NRVPN1 cron.err crond[1296]: USER root pid 3826 cmd /usr/bin/nrcronclient
Oct 27 10:14:01 NRVPN1 cron.err crond[1296]: USER root pid 4060 cmd /usr/bin/nrcronclient
Oct 27 10:15:01 NRVPN1 cron.err crond[1296]: USER root pid 4294 cmd /usr/bin/nrcronclient
Oct 27 10:16:01 NRVPN1 cron.err crond[1296]: USER root pid 4528 cmd /usr/bin/nrcronclient
Oct 27 10:17:01 NRVPN1 cron.err crond[1296]: USER root pid 4762 cmd /usr/bin/nrcronclient
Oct 27 10:18:01 NRVPN1 cron.err crond[1296]: USER root pid 4996 cmd /usr/bin/nrcronclient
Oct 27 10:19:01 NRVPN1 cron.err crond[1296]: USER root pid 5230 cmd /usr/bin/nrcronclient
Oct 27 10:20:01 NRVPN1 cron.err crond[1296]: USER root pid 5464 cmd /usr/bin/nrcronclient
Oct 27 10:21:01 NRVPN1 cron.err crond[1296]: USER root pid 5698 cmd /usr/bin/nrcronclient
Oct 27 10:21:59 NRVPN1 user.info kernel: rtl8366s rtl8366s: applying initvals
Oct 27 10:22:00 NRVPN1 daemon.warn dnsmasq[1348]: failed to access /tmp/resolv.conf.auto: No such file or directory
Oct 27 10:22:00 NRVPN1 user.info firewall: removing lan (br-lan) from zone lan
Oct 27 10:22:00 NRVPN1 user.info kernel: br-lan: port 3(nrtap) entering disabled state
Oct 27 10:22:00 NRVPN1 user.info kernel: br-lan: port 2(eth0.1) entering disabled state
Oct 27 10:22:00 NRVPN1 user.info kernel: br-lan: port 1(eth0) entering disabled state
Oct 27 10:22:00 NRVPN1 user.info kernel: eth0: link down
Oct 27 10:22:00 NRVPN1 user.info kernel: device nrtap left promiscuous mode
Oct 27 10:22:00 NRVPN1 user.info kernel: br-lan: port 3(nrtap) entering disabled state
Oct 27 10:22:00 NRVPN1 user.info kernel: br-lan: port 2(eth0.1) entering disabled state
Oct 27 10:22:00 NRVPN1 user.info kernel: device eth0 left promiscuous mode
Oct 27 10:22:00 NRVPN1 user.info kernel: br-lan: port 1(eth0) entering disabled state
Oct 27 10:22:01 NRVPN1 user.info firewall: removing wan (eth1) from zone wan
Oct 27 10:22:01 NRVPN1 cron.err crond[1296]: USER root pid 6514 cmd /usr/bin/nrcronclient
Oct 27 10:22:01 NRVPN1 user.info kernel: eth1: link down
Oct 27 10:22:02 NRVPN1 user.notice ifup: Enabling Router Solicitations on loopback (lo)
Oct 27 10:22:02 NRVPN1 user.debug kernel: ar71xx: pll_reg 0xb8050010: 0x11110000
Oct 27 10:22:02 NRVPN1 user.info kernel: eth0: link up (1000Mbps/Full duplex)
Oct 27 10:22:02 NRVPN1 user.info kernel: device eth0 entered promiscuous mode
Oct 27 10:22:02 NRVPN1 user.info kernel: eth0: link down
Oct 27 10:22:02 NRVPN1 user.info kernel: device eth0 left promiscuous mode
Oct 27 10:22:03 NRVPN1 user.debug kernel: ar71xx: pll_reg 0xb8050010: 0x11110000
Oct 27 10:22:03 NRVPN1 user.info kernel: eth0: link up (1000Mbps/Full duplex)
Oct 27 10:22:03 NRVPN1 user.info kernel: device eth0 entered promiscuous mode
Oct 27 10:22:03 NRVPN1 user.info kernel: br-lan: port 1(eth0) entering forwarding state
Oct 27 10:22:03 NRVPN1 user.info kernel: br-lan: port 2(eth0.1) entering forwarding state
Oct 27 10:22:03 NRVPN1 user.info kernel: device nrtap entered promiscuous mode
Oct 27 10:22:03 NRVPN1 user.info kernel: br-lan: port 3(nrtap) entering forwarding state
Oct 27 10:22:04 NRVPN1 daemon.info dnsmasq[1348]: exiting on receipt of SIGTERM
Oct 27 10:22:04 NRVPN1 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Oct 27 10:22:04 NRVPN1 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Oct 27 10:22:04 NRVPN1 user.debug kernel: ar71xx: pll_reg 0xb8050014: 0x11110000
Oct 27 10:22:04 NRVPN1 user.info kernel: eth1: link up (1000Mbps/Full duplex)
Oct 27 10:22:04 NRVPN1 user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Oct 27 10:22:04 NRVPN1 user.info firewall: adding lan (br-lan) to zone lan
Oct 27 10:22:07 NRVPN1 daemon.info dnsmasq[7044]: started, version 2.55 cachesize 150
Oct 27 10:22:07 NRVPN1 daemon.info dnsmasq[7044]: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP
Oct 27 10:22:07 NRVPN1 daemon.info dnsmasq-dhcp[7044]: DHCP, IP range 192.168.1.100 -- 192.168.1.250, lease time 12h
Oct 27 10:22:07 NRVPN1 daemon.info dnsmasq[7044]: using local addresses only for domain lan
Oct 27 10:22:07 NRVPN1 daemon.info dnsmasq[7044]: reading /tmp/resolv.conf.auto
Oct 27 10:22:07 NRVPN1 daemon.info dnsmasq[7044]: using nameserver 68.87.72.130#53
Oct 27 10:22:07 NRVPN1 daemon.info dnsmasq[7044]: using nameserver 68.87.77.130#53
Oct 27 10:22:07 NRVPN1 daemon.info dnsmasq[7044]: using local addresses only for domain lan
Oct 27 10:22:07 NRVPN1 daemon.info dnsmasq[7044]: read /etc/hosts - 1 addresses
Oct 27 10:22:07 NRVPN1 daemon.info dnsmasq-dhcp[7044]: read /etc/ethers - 0 addresses
Oct 27 10:22:07 NRVPN1 user.notice ifup: Allowing Router Advertisements on wan (eth1)
Oct 27 10:22:08 NRVPN1 user.info firewall: adding wan (eth1) to zone wan
Oct 27 10:22:10 NRVPN1 user.info firewall: adding lan (br-lan) to zone lan
Oct 27 10:22:10 NRVPN1 user.info firewall: adding wan (eth1) to zone wan
Oct 27 10:23:01 NRVPN1 cron.err crond[1296]: USER root pid 7836 cmd /usr/bin/nrcronclient
Oct 27 10:23:41 NRVPN1 user.info kernel: rtl8366s rtl8366s: applying initvals
Oct 27 10:23:41 NRVPN1 daemon.warn dnsmasq[7044]: failed to access /tmp/resolv.conf.auto: No such file or directory
Oct 27 10:23:41 NRVPN1 user.info firewall: removing lan (br-lan) from zone lan
Oct 27 10:23:41 NRVPN1 user.info kernel: br-lan: port 3(nrtap) entering disabled state
Oct 27 10:23:41 NRVPN1 user.info kernel: br-lan: port 2(eth0.1) entering disabled state
Oct 27 10:23:41 NRVPN1 user.info kernel: br-lan: port 1(eth0) entering disabled state
Oct 27 10:23:42 NRVPN1 user.info kernel: eth0: link down
Oct 27 10:23:42 NRVPN1 user.info kernel: device nrtap left promiscuous mode
Oct 27 10:23:42 NRVPN1 user.info kernel: br-lan: port 3(nrtap) entering disabled state
Oct 27 10:23:42 NRVPN1 user.info kernel: br-lan: port 2(eth0.1) entering disabled state
Oct 27 10:23:42 NRVPN1 user.info kernel: device eth0 left promiscuous mode
Oct 27 10:23:42 NRVPN1 user.info kernel: br-lan: port 1(eth0) entering disabled state
Oct 27 10:23:42 NRVPN1 user.info firewall: removing wan (eth1) from zone wan
Oct 27 10:23:43 NRVPN1 user.info kernel: eth1: link down
Oct 27 10:23:43 NRVPN1 user.notice ifup: Enabling Router Solicitations on loopback (lo)
Oct 27 10:23:43 NRVPN1 user.debug kernel: ar71xx: pll_reg 0xb8050010: 0x11110000
Oct 27 10:23:43 NRVPN1 user.info kernel: eth0: link up (1000Mbps/Full duplex)
Oct 27 10:23:43 NRVPN1 user.info kernel: device eth0 entered promiscuous mode
Oct 27 10:23:43 NRVPN1 user.info kernel: eth0: link down
Oct 27 10:23:43 NRVPN1 user.info kernel: device eth0 left promiscuous mode
Oct 27 10:23:44 NRVPN1 user.debug kernel: ar71xx: pll_reg 0xb8050010: 0x11110000
Oct 27 10:23:44 NRVPN1 user.info kernel: eth0: link up (1000Mbps/Full duplex)
Oct 27 10:23:44 NRVPN1 user.info kernel: device eth0 entered promiscuous mode
Oct 27 10:23:44 NRVPN1 user.info kernel: br-lan: starting userspace STP failed, starting kernel STP
Oct 27 10:23:44 NRVPN1 user.info kernel: br-lan: topology change detected, propagating
Oct 27 10:23:44 NRVPN1 user.info kernel: br-lan: port 1(eth0) entering forwarding state
Oct 27 10:23:44 NRVPN1 user.info kernel: device nrtap entered promiscuous mode
Oct 27 10:23:44 NRVPN1 user.info kernel: br-lan: topology change detected, propagating
Oct 27 10:23:44 NRVPN1 user.info kernel: br-lan: port 2(nrtap) entering forwarding state
Oct 27 10:23:45 NRVPN1 daemon.info dnsmasq[7044]: exiting on receipt of SIGTERM
Oct 27 10:23:45 NRVPN1 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Oct 27 10:23:45 NRVPN1 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Oct 27 10:23:45 NRVPN1 user.debug kernel: ar71xx: pll_reg 0xb8050014: 0x11110000
Oct 27 10:23:45 NRVPN1 user.info kernel: eth1: link up (1000Mbps/Full duplex)
Oct 27 10:23:45 NRVPN1 user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Oct 27 10:23:45 NRVPN1 user.info firewall: adding lan (br-lan) to zone lan
Oct 27 10:23:48 NRVPN1 daemon.info dnsmasq[8993]: started, version 2.55 cachesize 150
Oct 27 10:23:48 NRVPN1 daemon.info dnsmasq[8993]: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP
Oct 27 10:23:48 NRVPN1 daemon.info dnsmasq-dhcp[8993]: DHCP, IP range 192.168.1.100 -- 192.168.1.250, lease time 12h
Oct 27 10:23:48 NRVPN1 daemon.info dnsmasq[8993]: using local addresses only for domain lan
Oct 27 10:23:48 NRVPN1 daemon.warn dnsmasq[8993]: failed to access /tmp/resolv.conf.auto: No such file or directory
Oct 27 10:23:48 NRVPN1 daemon.info dnsmasq[8993]: read /etc/hosts - 1 addresses
Oct 27 10:23:48 NRVPN1 daemon.info dnsmasq-dhcp[8993]: read /etc/ethers - 0 addresses
Oct 27 10:23:48 NRVPN1 user.notice ifup: Allowing Router Advertisements on wan (eth1)
Oct 27 10:23:51 NRVPN1 user.info firewall: adding lan (br-lan) to zone lan
Oct 27 10:23:51 NRVPN1 user.info firewall: adding wan (eth1) to zone wan
Oct 27 10:24:01 NRVPN1 cron.err crond[1296]: USER root pid 9472 cmd /usr/bin/nrcronclient
Oct 27 10:24:07 NRVPN1 daemon.info dnsmasq[8993]: reading /tmp/resolv.conf.auto
Oct 27 10:24:07 NRVPN1 daemon.info dnsmasq[8993]: using nameserver 68.87.72.130#53
Oct 27 10:24:07 NRVPN1 daemon.info dnsmasq[8993]: using nameserver 68.87.77.130#53
Oct 27 10:24:07 NRVPN1 daemon.info dnsmasq[8993]: using local addresses only for domain lan
Oct 27 10:25:01 NRVPN1 cron.err crond[1296]: USER root pid 9874 cmd /usr/bin/nrcronclient
Oct 27 10:25:20 NRVPN1 user.info kernel: rtl8366s rtl8366s: applying initvals
Oct 27 10:25:20 NRVPN1 daemon.warn dnsmasq[8993]: failed to access /tmp/resolv.conf.auto: No such file or directory
Oct 27 10:25:20 NRVPN1 user.info firewall: removing lan (br-lan) from zone lan
Oct 27 10:25:20 NRVPN1 user.info kernel: br-lan: port 2(nrtap) entering disabled state
Oct 27 10:25:20 NRVPN1 user.info kernel: br-lan: port 1(eth0) entering disabled state
Oct 27 10:25:20 NRVPN1 user.info kernel: eth0: link down
Oct 27 10:25:20 NRVPN1 user.info kernel: device nrtap left promiscuous mode
Oct 27 10:25:20 NRVPN1 user.info kernel: br-lan: port 2(nrtap) entering disabled state
Oct 27 10:25:20 NRVPN1 user.info kernel: device eth0 left promiscuous mode
Oct 27 10:25:20 NRVPN1 user.info kernel: br-lan: port 1(eth0) entering disabled state
Oct 27 10:25:21 NRVPN1 user.info firewall: removing wan (eth1) from zone wan
Oct 27 10:25:22 NRVPN1 user.info kernel: eth1: link down
Oct 27 10:25:22 NRVPN1 user.notice ifup: Enabling Router Solicitations on loopback (lo)
Oct 27 10:25:23 NRVPN1 user.debug kernel: ar71xx: pll_reg 0xb8050010: 0x11110000
Oct 27 10:25:23 NRVPN1 user.info kernel: eth0: link up (1000Mbps/Full duplex)
Oct 27 10:25:23 NRVPN1 user.info kernel: device eth0 entered promiscuous mode
Oct 27 10:25:23 NRVPN1 user.info kernel: eth0: link down
Oct 27 10:25:23 NRVPN1 user.info kernel: device eth0 left promiscuous mode
Oct 27 10:25:23 NRVPN1 user.debug kernel: ar71xx: pll_reg 0xb8050010: 0x11110000
Oct 27 10:25:23 NRVPN1 user.info kernel: eth0: link up (1000Mbps/Full duplex)
Oct 27 10:25:23 NRVPN1 user.info kernel: device eth0 entered promiscuous mode
Oct 27 10:25:23 NRVPN1 user.info kernel: br-lan: starting userspace STP failed, starting kernel STP
Oct 27 10:25:23 NRVPN1 user.info kernel: br-lan: topology change detected, propagating
Oct 27 10:25:23 NRVPN1 user.info kernel: br-lan: port 1(eth0) entering forwarding state
Oct 27 10:25:23 NRVPN1 user.info kernel: device nrtap entered promiscuous mode
Oct 27 10:25:23 NRVPN1 user.info kernel: br-lan: topology change detected, propagating
Oct 27 10:25:23 NRVPN1 user.info kernel: br-lan: port 2(nrtap) entering forwarding state
Oct 27 10:25:24 NRVPN1 user.debug kernel: ar71xx: pll_reg 0xb8050014: 0x11110000
Oct 27 10:25:24 NRVPN1 user.info kernel: eth1: link up (1000Mbps/Full duplex)
Oct 27 10:25:24 NRVPN1 daemon.info dnsmasq[8993]: exiting on receipt of SIGTERM
Oct 27 10:25:24 NRVPN1 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Oct 27 10:25:24 NRVPN1 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Oct 27 10:25:24 NRVPN1 user.notice ifup: Enabling Router Solicitations on lan (br-lan)
Oct 27 10:25:25 NRVPN1 user.notice ifup: Allowing Router Advertisements on wan (eth1)
Oct 27 10:25:25 NRVPN1 user.info firewall: adding lan (br-lan) to zone lan
Oct 27 10:25:26 NRVPN1 user.info firewall: adding wan (eth1) to zone wan
Oct 27 10:25:27 NRVPN1 daemon.info dnsmasq[10998]: started, version 2.55 cachesize 150
Oct 27 10:25:27 NRVPN1 daemon.info dnsmasq[10998]: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP
Oct 27 10:25:27 NRVPN1 daemon.info dnsmasq-dhcp[10998]: DHCP, IP range 192.168.1.100 -- 192.168.1.250, lease time 12h
Oct 27 10:25:27 NRVPN1 daemon.info dnsmasq[10998]: using local addresses only for domain lan
Oct 27 10:25:27 NRVPN1 daemon.info dnsmasq[10998]: reading /tmp/resolv.conf.auto
Oct 27 10:25:27 NRVPN1 daemon.info dnsmasq[10998]: using nameserver 68.87.72.130#53
Oct 27 10:25:27 NRVPN1 daemon.info dnsmasq[10998]: using nameserver 68.87.77.130#53
Oct 27 10:25:27 NRVPN1 daemon.info dnsmasq[10998]: using local addresses only for domain lan
Oct 27 10:25:27 NRVPN1 daemon.info dnsmasq[10998]: read /etc/hosts - 1 addresses
Oct 27 10:25:27 NRVPN1 daemon.info dnsmasq-dhcp[10998]: read /etc/ethers - 0 addresses
Oct 27 10:25:30 NRVPN1 user.info firewall: adding lan (br-lan) to zone lan
Oct 27 10:25:30 NRVPN1 user.info firewall: adding wan (eth1) to zone wan
Oct 27 10:26:01 NRVPN1 cron.err crond[1296]: USER root pid 11556 cmd /usr/bin/nrcronclient
Oct 27 10:27:01 NRVPN1 cron.err crond[1296]: USER root pid 11959 cmd /usr/bin/nrcronclient
Oct 27 10:28:01 NRVPN1 cron.err crond[1296]: USER root pid 12361 cmd /usr/bin/nrcronclient
Oct 27 10:28:52 NRVPN1 user.info firewall: adding lan (br-lan) to zone lan
Oct 27 10:28:52 NRVPN1 user.info firewall: adding wan (eth1) to zone wan
Oct 27 10:29:01 NRVPN1 cron.err crond[1296]: USER root pid 12852 cmd /usr/bin/nrcronclient
Oct 27 10:30:01 NRVPN1 cron.err crond[1296]: USER root pid 12862 cmd /usr/bin/nrcronclient
Oct 27 10:31:00 NRVPN1 user.info firewall: adding lan (br-lan) to zone lan
Oct 27 10:31:00 NRVPN1 user.info firewall: adding wan (eth1) to zone wan
Oct 27 10:31:01 NRVPN1 cron.err crond[1296]: USER root pid 13306 cmd /usr/bin/nrcronclient
Oct 27 10:32:01 NRVPN1 cron.err crond[1296]: USER root pid 13312 cmd /usr/bin/nrcronclient
Oct 27 10:33:01 NRVPN1 cron.err crond[1296]: USER root pid 13335 cmd /usr/bin/nrcronclient


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: